An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Furuno FCV-600L, and methods of problem resolution. Unfortunately, networking and start-up of Furuno FCV-600L alone are not enough. Usually it results from the lack of time and certainty about functionalities of purchased items. safety signs and mark certificates which confirm compatibility with appropriate standards Why don't we read the manuals? rules of operation, control and maintenance of the Furuno FCV-600L item name of the manufacturer and a year of construction of the Furuno FCV-600L item informations concerning technical data of Furuno FCV-600L
#MANUAL FURUNO FCV 600L MANUAL#
What should a perfect user manual contain?įirst and foremost, an user manual of Furuno FCV-600L should contain: A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects. Unfortunately, only a few customers devote their time to read an instruction of Furuno FCV-600L. An instruction is a compilation of information about an item/a service, it is a clue. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. Therefore, in an instruction of Furuno FCV-600L one could find a process description. The term originates from the Latin word „instructio”, which means organizing. A necessary precondition for this is the unmistakable, legible character of an instruction. In accordance with the law, a customer can receive an instruction in non-paper form lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract.
I am due for a reef trip soon, so should be able to give more feedback later.The rules should oblige the seller to give the purchaser an operating instrucion of Furuno FCV-600L, along with an item. I am just running in my new motor though. So far it has told me that there were no fish under me, and sure enough there weren't any. I am pretty new to operating it, but I am very impressed with this sounder to date. You can set it up to show both beams at once on split-screen mode as well. The key to finding fish with this sounder seems to be to locate the general structure or fish with the wide (50 kHz) beam and then narrow it down with the 200kHz one. It picked up individual barras in this depth of water as distinct red circles, usually outlined by small yellow halos. One of them was in the Hinchinbrook channel and nearby creeks fishing for barramundi in 2-10 m of water. I have just got an FCV 600L, having used one or seen it used very effectively in two other boats. As you get deeper, the area increases and by the time you reach 20 m you are scanning an area of 7 m, which seems way too wide to me. This is more than double the width of my boat. If you have a 20 degree cone angle, at 13 m, you are scanning an area of about 4.6 m. I haven't checked the actual cone angles, but 11 degrees sounds heaps better than 20 to me. #Are you aware of these issues highlighted above? #What differences can you see on your screen at these depths? They get Airmar to build them a 20 degree, 200 kHz transducer." #Long story short, if you are fishing the bays and reefs I'd definitely stay away from the Furuno until #
Now, Furuno proponents will tell you to simply swith over to 50kHz in shallower water and get the #ģ7 degree cone angle but that too is flawed as at 50kHz you get little detail. Here's the skinny: Furuno's 200kHz has a 11 or so degree cone angle, while Garmin offers it with about 20 degrees. #Having said that let me say I own a 582 now and have owned probably a dozen Furuno machines in my life. If you are fishing offshore it is not an issue but if you are fishing in waters say 40' (about 12.2m) or less, think twice about the Furuno. Here is an extract form another Forum I found regarding COne angles for these Furunos - looks concerning from 12m down. Of course this assumes my transducer is mounted level from side to side and ignoring the slight forward angle to help dissipate air bubbles. #I am curious how far off of a small structure I could be while still marking it on the display. #Ultimately what I am trying to determine is at 30 to 50m of water depth how wide of a bottom scan is the machine showing. I am trying to find out what the official angle the transducer sends and receives its signal at both 50K & 200K.
0 kommentar(er)
